Aztec 16 Provozní pokyny

Operating instructions OI/ADS430–EN Rev. A Aztec ADS430Optical dissolved oxygen probeMeasurement made easyIntroductionThe ADS430 (RDO® PRO-X) probe is

10 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probeSalinity Correction Required when monitoring water containing high quantities o

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 116 CalibrationThis section describes how to calibrate the probe and involves me

12 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe6.2 1-Point calibration (water-saturated air)Referring to Fig. 6.1:1. Remove st

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 1311. If 1-Point Cal is displayed, go to step 14.If 1-Point Cal is not displayed

14 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe6.3 2-Point calibration (100 % and 0 % saturation)1. Perform a 1-point calibrat

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 1511. Use the / keys to select the probe to be calibrated and press the ke

16 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe21. Press the key (below the Continue prompt).The Calibrate page is displayed

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 177 Maintenance7.1 Cleaning the sensor cap1. Isolate the transmitter and remove

18 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe8 SpecificationSensor typeOptical (luminescent) dissolved oxygen sensorProbeIP

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 199 Spares and accessories9.1 Spares9.2 Accessories*See Section 3.5, page 6.Ackn

2 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probeContents1 Health & Safety ...

Contact usOI/ADS430–EN Rev. A 04.2015ABB LimitedProcess AutomationHoward Road, St. NeotsCambridgeshire, PE19 8EUUKTel: +44 (0)870 600 6122Fax: +44 (0

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 31 Health & Safety1.1 Document symbolsSymbols that appear in this document a

4 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe2 System overviewADS430 probe components are shown in Fig. 2.1:Fig. 2.1 ADS430 p

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 53 Installation3.1 Siting3.2 Probe dimensions3.3 Storing the sensor cap3.4 Fitti

6 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe3.5 Mounting / cleaning optionsProbe mounting / cleaning options are shown in Ta

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 74 Sensor setup – first-time installationTo perform a first-time installation (E

8 OI/ADS430–EN Rev. A | Aztec ADS430 | Optical dissolved oxygen probe5Sensor setup1. Connect the ADS430 probe to the transmitter’s EZLink connector –

Aztec ADS430 | Optical dissolved oxygen probe | OI/ADS430–EN Rev. A 95.1 Sensor SetupUsed to set the tag, measurement units, operational range and c